codentropy.com

Home > Dpm Error > Dpm Error 33123

Dpm Error 33123

Contents

Please paste the output here. -- Thanks, Hitesh Sharma [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. If the service fails to start, uninstall the protection agent by using Add or Remove Programs in Control Panel on . Explanation This error can occur when: An unidentified task ran, and the replica is invalid. Then retry the operation. 96 Job failure on replica of on caused by ongoing replica creation.

Select a different disk to add to the storage pool. 351 Disk cannot be added to the storage pool. Install the protection agent on each node of the server cluster. 370 Agent operation failed.   372 The agent operation failed because DPM detected a more recent version of the DPM Then retry the job. 99 Job failure on replica of on caused by ongoing stop-protection job. I ran a DBCC CHECKDB on it and > it > didn't find any issues either. > > I can see where the .MDF and .LDF files are.

Dpm Error 33123

If the service fails to start, re-install the protection agent. 224 DPM cannot browse because of a communication error with the agent. 1) Make sure that is Run consistency check and retry the operation. 195 Your changes cannot be applied because certain protection group properties have changed. DPM error ID = . Create a new protected group to add this data source.   156 The ability to add members to this protection group is temporarily disabled while initial synchronization of one or more

Restart and then try the recovery operation again. 239 is not protected. DPM does not support protection of clustered servers.   316 The protection agent operation on failed because the service did not respond. If you do not select the recommended library, ensure that you transfer the recovery tapes to the selected library after you finish the recovery wizard.   235 No library is available DPM will not use any volumes in which either operating system or DPM component are installed.   176 DPM failed to use the volume to create the replica since

asked 5 years ago viewed 1480 times active 5 years ago Related 2How to repeat failed tape backup attempt in DPM 2007?1Can DPM 2010 backup Exchange 2007 LCR enabled storage groups?0Best In the Management task area, on the Agents tab, select the protection agent, and then in the Actions pane click Uninstall. 312 The agent operation failed because the DPM Agent Coordinator Either the recovery point no longer exists or, if you selected a share for recovery, the path to its contents is missing from the recovery point. see here Yes No Tell us more Flash Newsletter | Contact Us | Privacy Statement | Terms of Use | Trademarks | © 2016 Microsoft © 2016 Microsoft

If you use DPM to protect data on this volume, you cannot restore operating system files or system state from this protection group member. Clear all unmounted directories from directory and then retry the operation. 358 The allocation of disk space for replica volumes failed because there is not enough unallocated disk Otherwise, troubleshoot the problem as follows: 1) Check the recent records from the DPMRA source in the Application Event Log on to find out why the agent failed to They both constantly get errors like this: "The replica of Volume D:\ on servername.domain.tld is not consistent with the protected data source.

Is Not Consistent With The Protected Data Source

Check the Alerts tab in the Monitoring task area to locate this alert and fix the issue. http://www.archivum.info/microsoft.public.dataprotectionmanager/2009-06/00200/Re-30135-Error.html If the operating system has been recently updated, Active Directory updates may still be pending. Dpm Error 33123 Some error messages contain placeholder text, such as . Dpm Error Id 93 Id 33123 see, 30301 and 30135, among others. 0 LVL 1 Overall: Level 1 Message Author Closing Comment by:espanolanthony2010-02-17 thanks 0 Write Comment First Name Please enter a first name Last Name

Subscribe to our monthly newsletter for tech news and trends Membership How it Works Gigs Live Careers Plans and Pricing For Business Become an Expert Resource Center About Us Who We For more information on resolving those errors, see the DPM Troubleshooting Guide (http://go.microsoft.com/fwlink/?LinkId=66740). My adviser wants to use my code for a spin-off, but I want to use it for my own company How much does a hat of disguise cost exactly? More Information DPM does not allow log, or incremental, backups for databases configured in the simple recovery model. 33123 Zip Code

If the primary DPM server database is protected, click OK to continue to the next step.   149 You have specified the change journal size on volume for .

Wait a few minutes after Windows starts for the agent to become available. To upgrade the protection agent: 1) In DPM Administrator Console, in the Management task area, on the Agents tab, select the computer on which the protection agent is installed, and then This may be a result of one or more disks in the DPM storage pool being offline or the deletion of volumes created by DPM to store the replicas.

You can filter the list only by computers that have been protected.   241 The volume on is not currently protected.   242 The share ""

Verify that the credentials you provided have administrator privileges on and then try to reinstall the protection agent again. 292 You cannot uninstall protection agents from the protected computers Select the SMTP Server tab to configure settings. 220 DPM cannot enable e-mail subscription for reports unless SMTP details are configured in the remote SQL Server Reporting Service installation. Create a valid recovery point on the primary DPM server and rerun the synchronization job. For more information, see "How to modify disk allocation" in DPM Help. 2) Rerun failed operation by clicking the link below. 59 DPM was used to trigger the recovery for

In the Management task area, select the Disks tab and review all disks that are owned by DPM. 367 DpmSync has completed with the following errors: . In these cases, identify the volume that corresponds to the recovery point volume for the data source in question from the "Modify Disk allocation" dialog box. Follow instructions to allocate disk space for protection. 169 Although you chose to retain the replica for this previously protected volume, the replica is now missing from the DPM server. For more information, see the DPM Deployment Guide. 3) To attach the computer correctly to this DPM server, run the SetDpmServer tool on the computer.

Restart the DPM Replication Agent service on . 53 DPM failed to communicate with because of a communication error with the protection agent. 1) Make sure that

Then retry the job. 114 Job failure on on caused by ongoing backup operation. Also, it was working fine before I upgraded to the >> > latest >> > service pack. >> > >> > Here's the DPM error: >> > The replica of SQL Symptoms Using System Center Data Protection Manager 2010 to backup a SQL database fails with the following error: Execution of SQL command failed for SQL Server 2005 database on . The selected recovery point is no longer available for recovery.

Either cancel the initial synchronization jobs for the members or wait until they complete. 157 cannot be added to protection because it is already a member of a If you find error address or can't find, please enter another address using the form bellow, then search again.If you want to delete this business in our database, please contact us Hornbeck // 0 Comments 0 0 0 Here’s an issue I ran into the other day and since I didn’t see a lot documented about it I thought I’d go ahead Check Disk Management to see whether the disk is online.

Uninstall DPM or the DPM protection agent from and install the DPM protection agent again from the computer that you want to use to protect the computer. 303 The Thanks. How do I space quads evenly? No action is needed.

Humans as batteries; how useful would they be? For Exchange mailbox recovery, DPM supports only the "Previous point in time" recovery option. Enter a different name. 138 The target path is located on the system volume. If you want to protect only this database, then you have to remove the Windows SharePoint Services farm from protection.   174 You cannot protect the selected Windows SharePoint Services data

Border
Go to top