codentropy.com

Home > Error Code > Dstv Error Code E18-4

Dstv Error Code E18-4

Contents

Service list descriptor containing the service is attached to a transport stream other than the transport stream currently tuned to. Page 1 of 2 1 2 > Thread Tools Display Modes #1 2013-09-06 , 16:53 Optimist Changes remote batteries hourly Join Date: Jul E39 optional E39 Locating Service Occurs when the service that is being watched is moved to a different transport stream. ECM Source D104 D104-6 No Vendor ID There is no vendor ID (card is not in and verified). http://codentropy.com/error-code/e16-4-error-code-dstv.html

If the problem persists, reboot your decoder. The service needs to be reset from MultiChoice. E49 optional E49 LNB Overload Occurs when the current drawn out of the front-end (to power the LNB) is excessive. the conclusion I came to was thta those older SC readers did not like "hot" removal insertion of SCs and thta it was better to switch off a decoder before removing

Dstv Error Code E18-4

Ask Your Question Fast! so if any body know our problem solve. Now this may no longer be true for the newer decoders. When the signal has been lost for longer than 30 seconds, the E52 banner should appear instead of E48.

A valid EMM PID was found and filters have been set-up. The smartcard will also return the CW to SoftCell as it is OK to descramble., thus this banner must appear together with Audio / Video. Smart Card D126 D126-4 PVR DRM OK PVR DRM OK. Clear Error Codes Dstv Mobile This priority is handled by SoftCell.

E48 - There is no signal The smartcard is not receiving a signal. Dstv Error Codes E30-4 This message occurs if there is an incompatibility between the smartcard field and the IRD into which the card has been inserted. Power-cycle your receiver by unplugging the power cord from the back of the receiver, wait 15 seconds, then plug the power cord back in E4000 - E4999 Login to your My i thought about this Your decoder might be in the incorrect bouquet selection.

Click here for instructions on sending a signal to your receivers. How To Reset Dstv Decoder After Payment This is due to a key mismatch between the playout and the smartcard or a Patch Filter fails for an ECM. Click here for instructions on sending a signal to your receivers. Yes | No CommentReplyReport

ljhan Level 9 (Master) 912 Answers, 90 Followers 0 0 Tweet Most of this problems are due to some illegal or unsupported update of your

Dstv Error Codes E30-4

This message occurs if there is an incompatibility between the Smart Card field and the IRD into which the card has been inserted. my site If your account is not suspended, then click on My Account to clear the error code or clear it using the form on the right part of the DSTV website. Dstv Error Code E18-4 Be Our Fan . Dstv Error Code E48 32 Smart Card E141 E141-4 Home gateway disallowed Home Gateway Proximity Control disallows the smartcard to be used for descrambling in the decoder.

E45 - Service not allowed SOLUTION:This service is not authorized. check my blog Read More E19 - Service is currently scrambled. This will not result in a message displayed on the screen. Session Management DRM E128 E128-4 No PVR subscription No PVR subscription. Dstv Error Code E16-4

E22 mandatory E22 Event Purchased The current event of the currently watched service is an IPPV event, and it has been purchased. Click here for instructions on sending a signal to your receivers. I think if you put a call through to their customer care they can assist you.Thanks mlungisi says: March 30, 2016 at 6:33 AM Reply for the past 2 days my this content Hope you found this post helpful?

Forum Home Register Today's Posts Search Forum > DStv Forum Archive (12 May 2014) > Service Queries > Service Queries > Comprehensive error code list Search via Google Please note that Dstv Self Service South Africa Since yesterday ReplyDeleteAnonymous12 December 2015 at 11:04My my Dstv is showing error E37-32 please help!ReplyDeleteRepliesEmmanuel Amadi13 December 2015 at 23:00Dear Anonymous, this could be an indication of poor or no signal E06 - Smartcard fault.

Linear ModeThreaded Mode VerwijderenWe gebruiken cookies om inhoud en advertenties relevanter te maken en je een veiligere ervaring te bieden.

Just click this link: [LINK VISIBLE TO REGISTERED USERS - CLICK HERE TO SEE THIS LINK].source: Samsung galaxy ace duos s6802 camera showing error call back.on error(-2147483648) how to solve it? If the problem persists then the decoder and/or the Smartcard might be damaged and must be tested, visit any DSTV office close to you. If you have forgotten your PIN, contact the DSTV Call Center. Dstv Self Service Reconnection Session Management DRM E135 E135-4 Record is not allowed Copy control disallows permanent copy.

E16 - Service is currently scrambled - Transmission might be temporarily suspended. SOLUTION:TV2 is not enabled. If the error codeE17re-appears use the form on the right on theDStv Websiteto clear the code or call your local MultiChoice Contact Centre. *E18 - Unknown Smartcard:The incorrect Smartcard is inserted have a peek at these guys Service list descriptor containing the service is attached to a transport stream other than the transport stream currently tuned to.

Power-cycle your receiver by unplugging the power cord from the back of the receiver, wait 15 seconds, then plug the power cord back in. Read More E32 - Service is currently scrambled Your Smartcard is not switched on or activated, or the channel that you are trying to view may not be part of your HUNT/FR1/FR2 HUNT, FR1 or FR2 codes indicate the box is searching for some type of frequency and generally requires no action. If the message reappears, reboot your decoder.

Power-cycle your receiver by unplugging the power cord from the back of the receiver, wait 15 seconds, then plug the power cord back in. E40 optional E40 Decoder Memory Full Decoder Memory Full E41 optional E41 Service is not currently available May occur when the IRD retrieves the PAT or PMT and the current event If E07 reappears, the decoder/Smartcard might be damaged and should be brought in for testing. E08 – CA Module failure The Control Access module is malfunctioning. Session Management DRM E134 E134-4 Number-of-playbacks limit exceeded Number-of-playbacks limit exceeded.

PVR Encryption D100 D100-31 0k Ok. It does not make sense. Please help us improve our content by removing questions that are essentially the same and merging them into this question. Note: upon this error, no further recording in this session can be done.

Session Management DRM E32 E32-4 Viewing is temporarily blocked, please stay tuned The viewer is not entitled to watch this service because surf locking is active. Want to know how to update your device? Join Date: Dec 2008 Posts: 11,768 One more I personally experienced this weekend after switching smartcards around; E12 - CA Module failure Not necessarily fatal, removing the smartcard for a short Newer Post Older Post Home Featured post LATEST MYTV SATELLITE, STRONG DECODER SETTINGS TO RECEIVE FREE-TO-AIR AND PAID CHANNELS A lot of our readers have been asking for the settings for

Thus not possible to present AV on the secondary TV E73 optional E73 TVLink Overload Occurs when the current drawn out of a TVLink supporting remodulator, is excessive. No message will appear on the screen, the status will only be shown on the CA Status screen.

Border