If this fails then the decoder and/or the smartcard has failed and should be returned to the supplier. E07 – Checking Smartcard - The decoder is checking the Smartcard. Firstly, read the rest of the message to see what it says. In case you have useful information on any of the error codes and repair methods, please let us know: E04 – Please insert smartcard - Your smartcard might have been inserted check over here
A reauthorisation is a clearance signal that can be performed either by a Multichoice agent through the call centre(011 289 2222) or your nearest agency. Remove the Smartcard, ensure that it is free of dust and re-insert it with the chip facing downwards and the arrows facing the decoder. If you have any other issues, Kindly leave your comments below. If the error is still present, contact the DSTV Call Center E42 - Parental Control PIN Blocked SOLUTION:This happens if you've set your parental control levels, but have forgotten your PIN https://selfservice.dstv.com/MyDStv/FixErrors
Posted in: TECH Newer Post Older Post Home 6 comments: Manoj Verma says: March 14, 2015 at 8:41 AM Reply My dstv is just searching for signals and after some time At the end of this post I will show you how to clear this error code online. *E17 - Service is currently scrambled:Transmission has been scrambled. ==>Solution:Reboot your decoder. If E07 reappears, reboot your decoder. This can cause any electronic system that is not unplugged, to blow.
Some of these simple challenges are seen in - clearing your E16 - 4 and other related error messages after subscription renewal, loss of signal, E06 - 4 errors, BE1 errors E107-4 means your decoder and smartcard are currently not paired. Share this:TwitterFacebookLike this:Like Loading... 268 Comments alegriya permalink My decoder is showing channel 100 only and payed. Dstv E45-32 An incorrect channel number was entered.
Reply Nandi permalink Good Day I have an explora on premium. If the error continues, reboot your decoder. Newer Post Home Featured post LATEST MYTV SATELLITE, STRONG DECODER SETTINGS TO RECEIVE FREE-TO-AIR AND PAID CHANNELS A lot of our readers have been asking for the settings for Strong decoders http://www.e18error.com/full_list_of_DSTV_error_codes.html The service needs to be reset from by MultiChoice.
Please select another bouquet by pressing TV on your remote, scrolling upto KU Africa and press OK.E70 - Services not available on TV2This channel is not available in your secondary viewing Dstv E45 Problem For the solution, connect decoder to the dish (satellite), power on and wait for 15 minutes. E37 – Invalid channel number SOLUTION:The channel number you selected is not in this viewing environment. Call your local MultiChoice Contact Centre *E32 - Service is currently scrambled:Your Smartcard is not switched on or activated. ==>Solution:Check that there are no outstanding payments on your account.
E43 - Not for this country DSTV doesn't have the rights to broadcast this channel in your country, which is why it cannot be viewed. http://digisattvworld.blogspot.com/2014/07/troubleshooting-your-dstv-decoder.html My Blog List Woman Wrapper Blog WHAT MAKES A WOMAN TIGHT Safe And Secure Nigeria Blog MOBILE FRAUD ALERT! Dstv Clear Error Messages An updated list of accredited installers can be obtained from your nearest MultiChoice office.Â Power failureFrequent power failures are experienced in some countries. Dstv Explora Error Codes To enable you maximize its use, it is important to know best ways to resolve most challenges without having to put a phone call across to the DStv Call Centre.
Reboot the decoder, and wait for about 5 minutes. Instead you pay the repair charge of the decoder that you will recieve when you swop your own decoder. This should work as a solution for GOTV / DSTV error code E48-32 / E016. E05 – Cannot read smartcard - an incorrect smartcard was inserted or the smartcard has been inserted incorrectly, or has collected dust. E50 Error Dstv
Yes that's right, I don't get paid for helping DSTV customers. If the same error message still comes up, contact your local engineer or visit any DSTV office nearby. I welcome you to join me on the social buttons by the right side of this blog for more interesting relations in promoting prevalent technologies in Nigeria, which the cable and this content E16 - Service is currently scrambled - Transmission might be temporarily suspended.
What could be the problem? E37-32 Dstv If after 30 seconds and the message remains displayed on screen, pull out and reinsert the smartcard. help me on what am supposed to do to continue enjoying View Comment Reply KWS Adams September 6, 2016 at 08:13 Try to call the customers service helpline and you will
View Comment Reply Salami Anike February 9, 2016 at 22:06 How to clear E42-38 error code View Comment Reply KWS Adams February 10, 2016 at 07:47 The entire guide on how When electricity is abruptly switched off and back on, this causes a power surge. Do you know that for every problem you experience with your decoder, there is always an error code that will be displayed on the screen? Dstv Error Codes E48-32 In as much as some of its...
If yes, then follow the CLEARING E16-4 reauthorization procedure and if it still persists, contact your service provider or any of their offices nearest to you. If the problem still persists, visit any DSTV office nearby. Go to www.dstv.com and click self-service, then located "Clear Code Error" to fix this issue. Categories ANDROID INTERNET/ BROWSING TIPS JOKES MOBILE TIPS NEWS PC TIPS TECH UNCATEGORIZED Download app .
E08: CA Module Failure The control access module is faulty Contact your local engineer or visit any DSTV office nearby E14: Service is currently Scrambled Transmission is temporarily suspended. SOLUTION: Remove the smartcard, ensure that it is free of dust and re-insert it with the chip facing downwards and the arrow facing the decoder. E38 - Program Map Table Not Available SOLUTION:Check that all cables from the satellite dish are securely connected to the correct inputs on the back of the decoder. Then either: -SMS "E17 + smartcard number to 32472 -or reset the service by logging into your account and selecting "reset decoder" E18 – Unknown Smartcard - an incorrect Smartcard is
Please wait for the scanning to finish. E30 means please wait a few minutes for your subscription status to be verified. When you see the error codes, you don't have to panic. Otherwise, buy lots and lots of airtime and try calling DSTV and see if they can help you.
Jobs | Careers Sunday, 17 August 2014 DSTV ERROR CODES, MEANING AND SOLUTIONS From Emmanuel Amadi in: CABLE & SATELLITE TV TECH If youare a user of theDStv decoder system, you The service needs to be reset from MultiChoice. Meer informatie, zoals over hoe je je instellingen kunt aanpassen, vind je hier: cookiebeleid.FacebookE-mail of telefoonWachtwoordAccount vergeten?RegistrerenEver had one of those messages on your TV screen? If you found the lift of DSTV error codes useful, please let us know.
Below are the codes and how to fix/remove them. *E04 - Please insert Smartcard:Your smartcard might have been inserted in the wrong slot or incorrectly. ==>Solution:Wipe the Smartcard with a soft E70 - Services not available on TV2 This channel is not available in your secondary viewing environment, so please try another channel. Apply the Reauthorization only for new activations. It is preferable to contact a MultiChoice Accredited Installer to check any installation related problem - you may, however, check the following yourself:The position of your dish.
If E07 persists, reboot the decoder. If the problem persists, reboot your decoder. E72 - Rescan in progress The decoder is busy scanning. If the error appears often, reboot the decoder. *E39 - Locating Service:The decoder is trying to locate the service. ==>Solution:Wait a couple of seconds until the service is located. *E42 -